Mould Manufacturers and Factories

Home Mould Products Molding Silicon Rubber for Casting of Poly Resin (CSN-8***P)

Molding Silicon Rubber for Casting of Poly Resin (CSN-8***P)

Molding Silicon Rubber for Casting of Poly Resin (CSN-8***P)
Price: Negotiable/Piece
Trade Terms: FOB,CFR,CIF
Min Order: 200kg
Pay Type: L/C,T/T
FEATURES:
1. Two-part silicone rubber: Flowable liquid silicone;
2. Cures at room temperature within 1-5 hours;
3. Excellent fluidity and good operability, easy to demold;
4. Good tensile and tear strength, low shrinkage;
5. High temperature resistance;
6. High duplication times.

TECHNICAL GUIDELINES:
1. Stir the liquid silicone (Part A and part B) well before use (except when depending on machine ).
2. This is a 100 Part A to 100 Part B mixing ratio by weight. Weigh the desire amount of part A into a clean mixing container, and then weight the proper amount of part B into the container. Mix the two component together by stirring with a stick. Scrape the container walls and bottom well to insure a thorough mix.
3. Though it is often unnecessary to deair the material due to its low viscosity and our special formulation, it is better to do so to obtain a bubble free rubber. If so, place the container into a vacuum chamber and evacuate the entrapped air from the mixture using a vacuum pump capable of achieving 29 inches of mercury vacuum. The mixture will rise, crest and then collapse in the container. Interruption(bumping) of the vacuum may be necessary to prevent overflowing the container. Keep the mixture under full vacuum for 2-3 minutes.
4. Bleed air slowly into the vacuum chamber. When the chamber is at atmospheric equilibrium, remove the cover plate and take out the container.
5. Pour the deaired material slowly in a steady stream from one end of the mould so that the material flows evenly over the pattern. This should minimize entrapment of air bubbles under the flowing material. A "ready" mold may be poured firstly over the pattern, which will also help reduce the possibility of entrapping air on the pattern and in the cured rubber. A mold release agent may be applied on the pattern first to improve release.
6. Allow the rubber to cure for 2-4 hours at 24C before removing the cured rubber mold from the pattern. Heat acceleration is recommended if necessary.
Model Features Application
CSN-8515P Low hardness, excellent toughness, high tear strength and outstanding chemical resistance, condensation cure Reproduction of decoration and handicrafts from poly resin, especially used in pouring and pieces mold
CSN-8520P Low hardness, excellent toughness, high tear strength and outstanding chemical resistance, condensation cure Reproduction of decoration and handicrafts from poly resin, especially used in pouring and pieces mold
CSN-8525P Moderate hardness, high tear strength, outstanding chemical resistance and durable in use, condensation cure Reproduction of decoration and handicrafts from poly resin, especially used in pouring and pieces mold
CSN-8530P Moderate hardness, outstanding chemical resistance and high tear strength, condensation cure Reproduction of decoration and handicrafts from poly resin, especially used in pieces mold and brushing mold of bigger sample.
CSN-8535P Moderate hardness, outstanding chemical resistance and high tear strength, condensation cure Reproduction of decoration and handicrafts from poly resin, especially used in pieces mold and brushing mold of outsize prototype.
CSN-8718P Good fluidity, low hardness, high tear strength, excellent toughness, extremely low shrinkage and less deformation, addition cure Reproduction of decoration and handicrafts with intricate detail from poly resin, especially used in pouring and pieces mold.
CSN-8720P Good fluidity, low hardness, high tear strength, excellent toughness, extremely low shrinkage and less deformation, addition cure Reproduction of decoration and handicrafts with intricate detail from poly resin, especially used in pouring and pieces mold.
CSN-8725P Moderate hardness, high tear strength, extremely low shrinkage and less deformation, addition cure Reproduction of decoration and handicrafts with intricate detail from poly resin, especially used in pieces mold and brushing mold of bigger prototype.
CSN-8730P Moderate hardness, high tear strength, extremely low shrinkage and less deformation, addition cure Reproduction of decoration and handicrafts with intricate detail from poly resin, especially used in pieces mold and brushing mold of bigger prototype.
CSN-8718PE Good fluidity, low hardness, high tear strength, excellent toughness, extremely low shrinkage, less deformation and easy to mix, addition cure Reproduction of decoration and handicrafts with intricate detail from poly resin, especially used in pouring and pieces mold.
CSN-8720PE Good fluidity, low hardness, high tear strength, excellent toughness, extremely low shrinkage, less deformation and easy to mix, addition cure Reproduction of decoration and handicrafts with intricate detail from poly resin, especially used in pouring and pieces mold.
CSN-8725PE Moderate hardness, high tear strength, extremely low shrinkage, less deformation and easy to mix, addition cure Reproduction of decoration and handicrafts with intricate detail from poly resin, especially used in pieces mold and brushing mold of bigger prototype.
CSN-8730PE Moderate hardness, high tear strength, extremely low shrinkage, less deformation and easy to mix, addition cure Reproduction of decoration and handicrafts with intricate detail from poly resin, especially used in pieces mold and brushing mold of bigger prototype.
CSN-8615P Low hardness, good toughness, tearing and chemical resistance, condensation cure. Reproduction of decoration and handicrafts from poly resin, especially used in pouring and pieces mold.
CSN-8620P Low hardness, good toughness, tearing and chemical resistance, condensation cure. Reproduction of decoration and handicrafts from poly resin, especially used in pouring and pieces mold.
CSN-8625P High tear strength, outstanding chemical resistance and durable in use, condensation cure. Reproduction of decoration and handicrafts from poly resin, especially used in pouring and pieces mold.
CSN-8630P Moderate hardness, outstanding chemical resistance and durable in use, condensation cure. Reproduction of decoration and handicrafts from poly resin, especially used in pieces mold.
CSN-8635P Moderate hardness, outstanding chemical resistance and durable in use, condensation cure. Reproduction of decoration and handicrafts from poly resin, especially used in pieces mold.

Prod Model: CSN-8***P
Markets: North America,South America,Eastern Europe,Southeast Asia,Africa,Oceania,Mid East,Eastern Asia,Western Europe
Viscosity (Cps 25 Degree)): 40000+/-5000
Pot Life(Min): 10-60
Demolding Time(H): 2-5
Hardness(Shore A): 15
Tensile Strength(Mpa): 4.2
Tear Strength(Kn/M): 25
Elongation(%): More Than 600
Shrinkage(%): Less Than 0.4
Material: Silicone Rubber
Appearance: Liquid
Guangzhou Conson Silicone Materials Co., Ltd. is a science and technology leading corporation, dedicated to research, develop, manufacture and sale silicone materials. We have complete research facilities and a high level R&D team, including over 10 engineers and two doctoral senior researchers. We also cooperate with many universities and scientific research institutes in researching and developing silicone materials. Furthermore, our sale and service team are professional, experienced and honest, We will do our best to provide high quality products, high grade services and competitive price for our customers.

Our products including 10 series in hundreds of kinds of silicone products like molding silicone rubber, silicone rubber for pad printing, encapsulant and potting silicone materials, silicone materials for LED manufacturing, thermal conductive silicone, silicone sealant, liquid silicone rubber for injection molding, liquid silicone rubber for textile label, et al. The application field of our products cover construction, decoration, crafts, costume, LED manufacturing, electronics, and so on. All products pass RoHS, SGS and FDA authentication and are currently been exported to Southeast Asia, Europe, the America and other 20 countries and regions.

We firmly believe that science and technology create the future and insist on the management concept of human oriented harmonious development. We regard the quality as our life and stick to manufacturing high quality silicone materials, and will continuously provide service with our advanced technologies and high grade products and perfect solutions as customed. We adhere to the tenet of faith, share and win-win, and look forward to join hands with you and strive for mutual prosperity.

Send your message to this manufacturer

  • Guangzhou Conson Silicone Materials Co., Ltd.

More >

Other Mould Products with This Manufacturers

About Us Mould Products Mould Manufacturers Hot Mould Mould News Mould Trade Shows Site Partners Contact Us Sitemap