Mould Manufacturers and Factories

Home Mould Products Silicone Rubber Pre-Mould Indoor (Outdoor) Termination

Silicone Rubber Pre-Mould Indoor (Outdoor) Termination

Silicone Rubber Pre-Mould Indoor (Outdoor) Termination
Price: US $ 20/Piece
Trade Terms: FOB,CFR,CIF
Min Order: 100/Set
Pay Type: L/C,T/T

8.7-15kV(17.5) Silicone Rubber Pre-mould Indoor(Outdoor)Termination
 
Applications:
Pre expanded indoor termination for 8.7/15(17.5)kV, single &3 core plastic insulated cable with tape/wire screen and with or without armour.
 
Features:
Quick, easy and safe installation.
High mechnical strength.
Wide cross section range.
Compact dimensions.
Unlimited shelf life.
 
8.7-15kV(17.5) Silicone Rubber Pre-mould Indoor(Outdoor)Termination Technical Data 
 
Test sequence
 
Item
 
Requirements acc. to IEC 60502.4 
 
8.7/15(17.5)kV
 
IEC 60502.4
 
1
 
AC withstand voltage test (in air and ambient temperature)  
 
AC for 5 min. at 39kV. No breakdown, No flashover
 
PASS
 
2
 
Partial discharge
 
10pC max. at 15kV
 
PASS
 
3
 
Impulse withstand test
 
10 impulses of each polarity at 95kV
 
PASS
 
4
 
Heating cycles  in air
 
30 cycles at  95ºC--100ºC and 22kV in air, No breakdown, No flashover
 
PASS
 
5
 
Heating cycles under water
 
30 cycles at  95ºC--100ºC and 22kV under water, No breakdown, No flashover
 
PASS
 
6
 
Partial discharge at  95ºC--100ºC 
 
10pC max. at 15kV
 
PASS
 
7
 
Thermal short-circuit (screen)
 
No visible deterioration at 3.0 kA, 1s
 
PASS
 
8
 
Thermal short-circuit (conductor)
 
No visible deterioration at 23.0 kA, 2s
 
PASS
 
9
 
Dynamic short-circuit
 
No visible deterioration at 81.0 kA, not less than 10 ms
 
PASS
 
10
 
Impulse withstand test at  95ºC--100ºC
 
10 impulses of each polarity at 95kV
 
PASS
 
11
 
AC withstand voltage test
 
AC for 15 min. at 22kV. No breakdown, No flashover
 
PASS
 
 
Table of specification of 8.7-15kV(17.5) Silicone Rubber Pre-mould Indoor(Outdoor)Termination
Voltage 1&3 core indoor(Outdoor)
Pre-mould termination Suit for cable Section
(mm 2 ) Insulation OD 
of Applicable Cables
8.7/15kV
 
I(O)CP-10/3(1).1#
 
35
 
16.2~18.2
 
I(O)CP-10/3(1).2# 50 17.8~19.6
I(O)CP-10/3(1).3# 70 19.5~21.0
I(O)CP-10/3(1).4# 95 20.5~22.5
I(O)CP-10/3(1).5# 120 22.0~24.3
I(O)CP-10/3(1).6# 150 23.5~25.8
I(O)CP-10/3(1).7# 185 25.0~27.4
I(O)CP-10/3(1).8# 240 27.0~29.5
I(O)CP-10/3(1).9# 300 29.5~32.0
I(O)CP-10/3(1).10# 400 32.5~34.8
I(O)CP-10/3(1).11# 500 34.0~37.5
Shijiazhuang Histe Electronic Co., Ltd was established in 1991. It is the earliest firm to produce prefab cold shrinkable cable accessories domestically. The firm is located in Shijiazhuang Lvdao Development Zone which is close to Qingdao-Yinchuan Super Highway neighboring the second circle-highway around Shijiazhuang city-the junction of Beijing-Guangzhou, Shijiazhuang(short for Shi)-Taiyuan, Shi-Dezhou railway. So its transport is very convenient.

Send your message to this manufacturer

  • Shijiazhuang Histe Electronic Co., Ltd

More >

Other Mould Products with This Manufacturers

About Us Mould Products Mould Manufacturers Hot Mould Mould News Mould Trade Shows Site Partners Contact Us Sitemap